owners manual Subaru Outback

all ratings: 0 average rating: 5

7-10 Starting and operating/Starting and stopping the engine (models without push–button ignition switch) enginehasnotwarmedupsufficiently).after the engine has started.matically lowers the idle speed as the In such a case, it is recommended thatIf the engine does not start, perform theengine warms up. you change to a different brand of fuel.following procedure. . On rare occasions, transient knock-(1) Turn the ignition switch to the! CVTmodels ing maybeheardfromtheenginewhen“LOCK” position and wait for at least the accelerator is operated rapidly10 seconds. After checking that theCAUTION such as a rapid start-up and a rapidparking brake is applied, turn the acceleration. This is not a malfunction.ignition switch to the “START” positionIf you restart the engine while the . The engine starts more easily whenwhile depressing the accelerator pedalvehicle is moving, shift the select the headlights, air conditioner and rearslightly (approximately a quarter of thelever into the “N” position. Do not window defogger are turned off.full stroke). Release the acceleratorattempt to place the select lever of a . After the engine starts, the enginepedal as soon as the engine starts.moving vehicle into the “P” posi- speedwill be kept high until the engine(2) If this fails to start the engine, turntion. has warmed up sufficiently.the ignition switch back to the “LOCK” position and wait for at least 101. Apply the parking brake. ! MTmodels seconds. Then fully depress the accel-2. Turn off unnecessary lights and ac- 1. Apply the parking brake.erator pedal and turn the ignitioncessories. 2. Turn off unnecessary lights and ac-switch to the “START” position. If the3. Shift the select lever to the “P” or “N” cessories. engine starts, quickly release theposition (preferably“P” position). The 3. Depress the clutch pedal to the flooraccelerator pedal.starter will only operate when the select and shift the shift lever into neutral. Hold(3) If this does not start the engine,lever is at the “P” or “N” position. the clutch pedal to the floor while startingturn the ignition switch again to the4. Turn the ignition switch to the “ON” the engine. The starter motor will only“LOCK” position. After waiting for 10position and check the operation of the operate when the clutch pedal is de-seconds or longer, turn the ignitionwarning and indicator lights. Refer to pressed fully to the floor.switch to the “START” position without“Warning and indicator lights” F3-12. 4. Turn the ignition switch to the “ON”depressing the accelerator pedal.5. Turn the ignition switch to the “START” position and check the operation of the(4) If the engine still refuses to start,position without depressing the accelera- warning and indicator lights. Refer tocontact your nearest SUBARU dealertor pedal. Release the key immediately “Warning and indicator lights” F3-12.for assistance.after the engine has started. 5. Turn the ignition switch to the “START”6. Confirm that all warning and indicatorIf the engine does not start, perform the position without depressing the accelera-lights have turned off after the engine hasfollowing procedure. tor pedal. Release the key immediatelystarted. The fuel injection system auto-(1) Turn the ignition switch to the

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders