or
owners manual Alfa Romeo 33
owners manual Alfa Romeo 33 - year of production: 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995 - Alfa Romeo 33 owners manual EN
Document:
pdf (12.9 MB) 378 pages
all ratings: 0
average rating: 5
text version of content this owner's manual page
from owners manual to the vehicle Alfa Romeo 33, year of production 1983 - 1995:
COMPLETE CAR
3. Check again engine timing.
4. Fit back camshaft support cov-
ers, alternator and water pump
control belt, electricfan and spark
plugs.
5. Start engine and warm it up to
normal running temperature, then
remove again camshaft support cov-
ers. Working on one cylinder head at
the time, proceed as follows: bring . A milky oil indicates the pres-
relevant camshaft in neutral position, ence of cooling water.
loosen and then tighten again idler Identify the cause and take
pulley lock nut thus giving the belt in corrective measures.
its final tension load. . An oil with extremely low
viscosity indicates dilution with
Key camshaft control belts. onto @ : Tightening torque petrol.
2.
crankshaft and camshaft pulleys
Idler pulley lock nut Using an oil filter wrench,
starting with the one of the left hand (warm engine) 2.
cylinder head. 29+35 N-m remove oil filter.
(1) Belt keying must take place
(3 + 3.6kg- m
while belt pulling section (opposite 21.38 f 25.8ft.lb)
the idler pulleys) is fully stretched.
(2) Loosen idler pulleys lock nuts all
the way and then tighten them again. 6. Fit back camshaft support cov-
(3) Let driving shaft rotate in the
ers and timing belts covers.
functioning direction so as to allow
belt to set on pulleys.
(4) Set, one by one, the camshafts
to the neutral position, then unloos-
CHANGING ENGINE OIL
en nuts securing backstand, press a
ANQ REPLACING OIL
few times on them and secure nuts to
the prescribed torque. FILTER
(5) Rotate crankshaft a few times in
its working direction so that belts
1. With engine warm, remove oil
may take up their final position.
filler cap and oil pan drain plug
3. When engine oil is completely
letting oil drain completely into a
drained, clean oil pan drain plug and
suitable container (wait at least 15
Rotate camshafts till they are in screw it back into place.
neutral position: loosen idler pulleys minutes). 4. Moisten the gasket of the new
lock nuts pressing idler pulleys afew oil filter and then install the filter
times, and then tighten relevant nuts tightening it all the way.
according to specified torque. 5. Refill engine with specified new
Rotate crankshaft a few times in its oil referring to LUBRICANTS&hart.
working direction thus allowing belts Check oil level with dipstick.
to settle on pulleys, and then repeat
above described tension checking
operation while positioning cam- ENGINE OIL QUANTITY
shafts one at the time- withcups
disengaged. 1 kg1 (lb)
Camshaft support sumps(*I 0.25(0.55)
@ : Tightening torque Engine oil sump 3.60 (7.94)
Idler pulley lock nut Sump capacity 3.15 (6.94)
0.45 (1 .OO)
(cold engine) Filter capacity
37+46 N-m
(3.8 + 4.7kg- m (*I Refill to be carried out, far each sump.
27.49 + 33.98ft-lb) in case of disassembly only.
May 1983 00-26
Download PDF
Click here to download a pdf file with an instruction manual for Alfa Romeo 33
year of production from: 1983
Do you prefer pdf format?
Find out how to download
Enter the code to download PDF file:
All pages in one PDF file!
How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.
:
Alfa Romeo 33 owners manual
pages 20 - 26
Alfa Romeo 33 owners manual
page 23 / 378
this site is maintained by advertising - for view instructions, turn off ad blocking in your browser
Download PDF
Others owner's manuals for this model: