owners manual Seat Mii

all ratings: 0 average rating: 5

Advice 5 Tube for inflating tyres direction. The seal on the mouth of the bottle●Keep the air compressor running until it moves automatically. reaches 2.0 to 2.5 bar (29-36 psi / 6 Warning provided by tyre pressure moni- 1) 200-250 kPa) ››› . Maximum operation time toring system ●Remove the lid from the filling tube 8 minutes ››› . 2) ››› Fig. 132 3 and screw the open end of the 7 Air bleed screw tube into the tyre valve. ●Disconnect the air compressor. 8 ON/OFF switch ●Hold the tyre sealant can upside down and ●If it is not possible to achieve an air pres- 9 12 volt connector fill the complete contents of the can into thesure of 2.0 to 2.5 bar (29-36 psi / 10 Bottle of sealant tyre. 200-250 kPa), unscrew the tyre inflator tube from the tyre valve. 11 Spare tyre valve ● Remove the tyre sealant bottle from the valve. ●Move the vehicle some 10 metres forward The valve insert remover 1 has a gap at the or backward so that the sealant is evenly dis- ●Screw the valve insert again with the corre- lower end for a valve insert. The valve insert tributed in the tyre interior. sponding enclosed extractor ››› Fig. 132 1 can only be screwed or unscrewed in this into the tyre valve. ●Securely screw the compressor tyre inflator way. This also applies to its replacement part 11 . tube into the tyre valve and repeat the infla- Inflating the tyre tion process. ●If the indicated pressure can still not be ●Securely screw the tyre inflator tube Sealing and inflating a tyre 5 reached, the tyre is too badly damaged. The ››› Fig. 132 of the compressor into the tyre tyre cannot be sealed with the anti-puncture valve. Sealing a tyre kit. Do not continue driving. You should ob- ●Check whether the air bleed screw tain professional assistance ››› . ●Unscrew the tyre valve cap. ››› Fig. 132 7 is closed. ●Disconnect the air compressor and unscrew ●Use the corresponding enclosed extractor ●Start the vehicle engine and leave it run- the flexible inflator tube from the tyre valve. ››› Fig. 132 1 to unscrew the tyre valve in- ning. sert. Place the valve insert on a clean surface. ●When the tyre pressure is between 2.5 and ●Attach the connector ››› Fig. 132 9 to a 12 2.0 bars, immediately continue driving with- ●Vigorously shake the sealant bottle volt socket of the vehicle ››› page 72. out exceeding 80 km/h (50 mph). ››› 10 Fig. 132 for several seconds. ●Connect the air compressor with the ●After 10 minutes, Check the pressure again ●Screw the inflator tube ››› Fig. 132 3 se- ON/OFF switch ››› Fig. 132 8 . ›› page 181. › curely into the sealant bottle in a clockwise 1) It can also be integrated in the compressor. 2) In its place, the compressor may have a button. 180

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders