owners manual Skoda Rapid

all ratings: 0 average rating: 5

›On vehicles with automatic transmission, place the selector lever in the P Preparations for using the breakdown kit position. Read and observe on page Ėěě first. ›Start the engine and run it in idle. ›Plug the connector ě into the Ėė-volt socket » page ĜĚ. 0he following preparatory work must be carried out before using the puncture ›Switch on the air compressor with the ON and OFF switch Ğ . repair kit. ›Allow the air compressor to run until a pressure of ė.ĕ - ė.Ě bar is achieved. Maximum run time of ĝ minutes » . ›Switch off the engine. ›Switch off the air compressor. ›For vehicles with manual transmission select gear Ė. ›If you cannot reach an air pressure of ė.ĕ - ė.Ě bar, unscrew the tyre inflation ›On vehicles with automatic transmission, place the selector lever in the P hose Ĝ from the tyre valve. position. ›Drive the vehicle Ėĕ metres forwards or backwards to allow the sealing agent ›Firmly apply the handbrake. to “distribute” in the tyre. ›Check that you can carry out the repairs with the breakdown kit » page Ėěě, ›Firmly screw the tyre inflation hose Ĝ back onto the tyre valve and repeat General information. the inflation process. ›1ncouple trailer, if attached. ›Switch off the air compressor. ›Remove the breakdown kit from the boot. ›Remove the tyre inflation hose Ĝ from the tyre valve. ›Stick the sticker Ė » Fig. ĖĜĖ on page Ėěě on the dashboard in the driver's field of view. Once a tyre inflation pressure of ė.ĕ - ė.Ě bar is achieved, you can continue the ›1nscrew the valve cap. journey. ›1se the valve remover ė to unscrew the valve core and place it on a clean 3ARNING surface (rag, paper, etc.). ■ If the tyre cannot be inflated to at least. ė.ĕ bar, the damage is too great. 0he sealing agent cannot be used to seal the tyre.  Do not continue to Sealing and inflating the tyre drive! Seek help from a specialist garage. Read and observe on page Ėěě first. ■ 0he tyre inflation hose and air compressor may get hot as the tyre is be- ing inflated – there is a risk of burning. Sealing Forcefully shake the tyre inflater bottle Ėĕ » Fig. ĖĜĖ on page Ėěě back and › CA10ION forth several times. Switch off the air compressor after running ĝ minutes at the latest – there is a Firmly screw the inflation hose Ę onto the tyre inflater bottle Ėĕ. 0he film on › risk of overheating! Allow the air compressor to cool a few minutes before the cap is pierced automatically. switching it on again. ›Remove the plug from the inflation hose Ę and plug the open end fully onto the tyre valve. Hold the bottle Ėĕ with the bottom facing upwards and fill all of the sealingNotes for driving with tyre repaired › agent from the tyre inflater bottle into the tyre. Read and observe on page Ėěě first. ›Remove the filler plug from the tyre valve. ›Screw the valve core back into the tyre valve using the valve remover ė . 0he inflation pressure of the repaired tyre must be checked after driving for Ėĕ minutes. Inflating ›Screw the tyre inflation hose Ĝ » Fig. ĖĜĖ on page Ėěě of the air compressor If the tyre pressure is Ė.Ę bar or less firmly onto the tyre valve. › Do not continue to drive! 0he tyre cannot be properly sealed with the ›For vehicles with manual transmission the lever into the neutral position.  breakdown kit. Emergency equipment and self-helpĖěĜ

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders