owners manual Skoda Rapid

all ratings: 0 average rating: 5

3ARNING (Continued) Follow-up work ■ Never position any body parts, such as arms or legs under the vehicle, After changing the wheel, the following work must be carried out. while the vehicle is raised with a lifting jack. ■ 3hen the vehicle is raised, never start the engine. ›Stow the replaced wheel in the wheel well and secure it with a special screw. ›Stow the tool kit in the space provided and secure using the band. CA10ION ›Check the tyre pressure on the installed wheel as soon as possible. ›Have the tightening torque of the wheel bolts checked with a torque wrench It is important to ensure that the jack is correctly attached to the web of the as soon as possible. lower fork leg, otherwise there is a risk of damage to the vehicle occurring. After changing the wheel, the tyre pressure should be adjusted. In vehicles Remove the wheel / fix with tyre pressure monitoring, save tyre pressure values» page Ėėĕ. 3hen changing a wheel, the following instructions must be followed.Replace the damaged wheel or consult a specialist garage about repair op- tions. ›Remove the full wheel trim or the caps of the wheel bolts. ›First of all slacken the anti-theft wheel bolt and then the other wheel bolts.0he prescribed tightening torque of the wheel bolts is Ėėĕ Nm. ›Jack up the vehicle until the wheel that needs changing is clear of the 3ARNING ground. 1nscrew the wheel bolts and place them on a clean surface (cloth, paper,■ If the wheel bolts are tightened to a too low tightening torque, the rim › etc.). can come loose when the car is moving. A tightening torque which is too Remove the wheel carefully. high can damage the bolts and threads and this can result in permanent › Attach the wheel and slightly screw on the wheel bolts. deformation of the contact surfaces on the rim. › Lower the vehicle. ■ Drive cautiously and only at a moderate speed until the tightening torque › Alternately tighten wheel bolts opposite (diagonally) with the wheel wrench.has been checked. › 0ighten the anti-theft wheel bolt last. ›Replace the wheel trim or the caps. Puncture set 3hen fitting unidirectional tyres, ensure that the direction of rotation is cor- rect » page ĖĚĜ. Introduction All bolts must be clean and must turn easily. 0his chapter contains information on the following subjects: If it is established when changing a wheel that the wheel bolts are corroded Components of the puncture repair kits Ėěě and difficult to move, then these must be replaced. General information Ėěě 1nder no circumstances grease or oil the wheel bolts! Preparations for using the breakdown kit ĖěĜ Sealing and inflating the tyre ĖěĜ 3ARNING Notes for driving with tyre repaired ĖěĜ 1ndo the wheel bolts only a little (about one turn) provided that the vehicle has not yet been jacked up. Otherwise the wheel could become loose and1se the breakdown kit to reliably repair tyre damage caused by foreign bodies fall off. or a puncture with diameters up to approx. ę mm. A repair made using the breakdown kit is never intended to replace a perma- nent repair on the tyre. Its purpose is to get you to the nearest specialist ga-  rage. Emergency equipment and self-helpĖěĚ

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders