owners manual Seat Toledo

all ratings: 0 average rating: 5

Advice – Fix the sticker 2 ››› Fig. 128 ››› page 155Inflating the tyre not be repaired using the tyre sealant kit onto the dash panel where the driver will ››› . – Screw the tyre filling hose 5 ››› Fig. 128 see it. ››› page 155 firmly onto the tyre valve.– Switch the compressor off. – Do not remove the foreign body, e.g. bolts – Make sure that the bleed screw 7 is – Unscrew the flexible hose 5 from the tyre or nails, from the tyre. closed. valve. – Unscrew the tyre valve cap. – Start the vehicle engine and leave it run- When a tyre pressure of 2.0-2.5 bar – 1 ning. Using the valve extractor , unscrew the (29-36 psi/200-250 kPa) is reached, you can valve insert and place it on a clean surface continue driving at a max. speed of 80 km/h – Plug connector 9 into the 12-volt power (cloth, paper, etc.) (50 mph). socket. Check the tyre pressure after 10 minutes of – Turn on the air compressor with switch 8 . driving ››› page 157. Filling and inflating the tyre – Leave the air compressor running until the tyre pressure has reached 2.0 -2.5 bar WARNING Filling the tyre (29-36 psi/200-250 kPa). The max. operat- ● The flexible tyre filling hose and the air 10 ing time for the compressor is 8 minutes – Shake the tyre sealant can ››› Fig. 128 compressor may heat up during the filling ››› ! ››› page 155 thoroughly several times. process. Risk of injury! – Switch the compressor off. ● – Att 3 Do not place the hot flexible tyre filling ach the flexible filling hose onto the 10 hose or hot air compressor on top of flamma- can . The foil sealing the can will be au- – When an air pressure of 2.0-2.5 bar ble materials. Risk of fire! tomatically pierced. (29-36 psi/200-250 kPa) cannot be ● If the tyre cannot be inflated to a minimum reached, unscrew the flexible tube 5 from – Remove the cap from the flexible filling pressure of 2.0 bar (29 psi/200 kPa), then the tyre valve. hose 3 and insert the open end as far as it the tyre is too badly damaged. The sealing will go into the tyre valve. – Drive the vehicle approx. 10 metres for-product is unable to seal the tyre . Do not wards or backwards, so that the sealantcontinue driving and obtain professional as- – Hold the can 10 upside down and fill the sistance. can “spread evenly” in the tyre. complete contents of the can into the tyre. – Screw the flexible hose from the air com- – Remove the empty can from the tyre. CAUTION pressor 5 back onto the tyre valve and re- – Screw the valve insert back into the tyre peat the inflation process. Do not use the air compressor for longer than valve using the valve extractor 1 . 8 minutes at a time. Risk of overheating! Be- – If the pressure is still lower than specified, fore using the air compressor again, leave it the tyre is too badly damaged. The tyre can- to cool down for several minutes. 156

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders