owners manual Skoda Kodiaq

all ratings: 0 average rating: 5

Firmly screw the inflation hose Ę onto the tyre inflater bottle Ėĕ. 0he film on › CA10ION the cap is pierced automatically. Switch off the air compressor after running ě minutes at the most – risk of ›Remove the plug from the inflation hose Ę and plug the open end fully onto overheating! Allow the air compressor to cool a few minutes before switching the tyre valve. it on again. Hold the bottle Ėĕ with the bottom facing upwards and fill all of the sealing › agent from the tyre inflator bottle into the tyre. Information for driving with repaired tyres ›Remove the filler plug from the tyre valve. Screw in the valve insert using the valve remover ė . Read and observe on page ėĞě first. ›  Inflating 0he inflation pressure of the repaired tyre must be checked after driving for Ėĕ ›Screw the air compressor tyre inflation hose Ĝ » Fig. ĘęĞ on page ėĞě firmly minutes. onto the tyre valve. If the tyre inflation pressure is Ė.Ę bar or less ›For vehicles with manual transmission, set the lever in the neutral position. ›0he tyre cannot be properly sealed with the breakdown kit.  Do not drive ›On vehicles with automatic transmission, place the selector lever in the P the vehicle! Seek help from a specialist garage. position. ›Start the engine. If the tyre inflation pressure is Ė.Ę bar or more ›Plug the connector ě into Ėė volt socket » page ĞĜ. ›Set the tyre pressure back to the correct value » page ėĝě. ›Switch on the air compressor with the ON and OFF switch Ğ . ›Continue driving carefully to the nearest specialist garage at a maximum ›Once a tyre inflation pressure of ė.ĕ-ė.Ě bar is reached, turn off the air com- speed of ĝĕ km/h (Ěĕ mph). pressor. Maximum run time of ě minutes » . ›If you cannot reach an air pressure of ė.ĕ - ė.Ě bar, unscrew the tyre inflation3ARNING hose Ĝ from the tyre valve. A tyre filled with sealant has the same driving characteristics as a standard ›Drive the vehicle approx. Ėĕ metres forwards or backwards to allow the seal- tyre. 0he following guidelines must be observed. ing agent to “distribute” in the tyre. ■ Do not drive faster than ĝĕ km/h (Ěĕ mph). ›Firmly screw the tyre inflation hose Ĝ back onto the tyre valve and repeat ■ Avoid accelerating at full throttle, sharp braking and fast cornering. the inflation process. ›Stick the corresponding sticker Ė on the dashboard in the driver's field of view. Jump-starting Once a tyre inflation pressure of ė.ĕ – ė.Ě bar is achieved, continue the journey Introduction at a maximum speed of ĝĕ km/h (Ěĕ mph). 0his chapter contains information on the following subjects: 3ARNING Jump-starting using the battery from another vehicle ėĞĝ ■ If it is not possible to inflate the tyre to at least. ė.ĕ bar, the damage is too great. 0he sealing agent cannot be used to seal the tyre.  Stop driv- 3ARNING ing! Seek help from a specialist garage. ■ 0he following instructions must be followed at all times when working on ■ 0he tyre inflation hose and air compressor may get hot as the tyre is be- the engine compartment » page ėĜĝ. ing inflated – risk of burning. ■ 3hen handling the vehicle battery, the following warnings must be ob-  served » page ėĝĘ. Emergency equipment and self-help ėĞĜ

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders