owners manual Skoda Kodiaq

all ratings: 0 average rating: 5

3ARNING Changing a wheel A tightening torque which is too high can damage the bolts and threads ›0ake out the emergency or spare wheel » page ėĞė. and this can result in permanent deformation of the contact surfaces on ›Remove the full wheel trim » page ėĞĘ or caps » page ėĞę. the rim. 0oo low tightening torque, the wheels may fall off while driving - ›Loosen the wheel bolts » page ėĞę » . risk of an accident. Drive cautiously and only at a moderate speed until the ›Jack up the vehicle» page ėĞĚ until the wheel that needs changing is clear of tightening torque has been checked. the ground. ›1nscrew the wheel bolts and place them on a clean surface (cloth, paper, Removing/stowing the emergency or spare wheel etc.). ›Remove the wheel carefully. ›Attach the spare wheel and slightly screw on the wheel bolts. Fig. Ęęė ›Lower the vehicle. 0ake out the wheel ›0ighten the wheel bolts opposite each other using the wheel wrench (“alter- nating crosswise”)» page ėĞę. ›Replace the wheel trim » page ėĞĘand the caps » page ėĞę. 3hen fitting a wheel with unidirectional tyres, ensure that the direction of ro- tation is correct » page ėĝě. All bolts must be clean and must turn easily. If the screws are corroded and dif- ficult to move, then these must be replaced. 0he spare wheel is located in a well under the floor covering in the luggage compartment and is fixed in place with a fastening screw. 3ARNING ■ 1ndo the wheel bolts just a little (about one turn) while the vehicle is not 0ake out the wheel jacked up. Otherwise, the wheel could come off and fall down – there is a ›Fold down the backrests of the third seat row (applies to the seven-seat ver- risk of injury. sion) » , ■ 1nder no circumstances grease or oil the wheel bolts - risk of accident! ›Lift the floor covering and fold upward the variable loading floor and flooring covering. ›At the same time, pull the two release loops of the third seat row and lift the Subsequent steps seats (applies to the seven-seat version). ›Loosen the retaining belt and take out the box with the tool kit. After changing the wheel, the following work must be carried out. ›1nscrew the locking screw in the direction of arrow » Fig. Ęęė and the re- ›Stow the replaced wheel in the well under the floor covering of the luggage move the wheel. compartment and secure with a locking screw. ›Stow the tool kit in the space provided and secure using the band.Store wheel away ›Check and, if necessary, adjust the tyre pressure on the assembled wheel,›Place the wheel into the wheel well with the wheel rim pointing downward. and, for vehicle with tyre pressure monitoring, save the tyre pressure values›Pull the fixing band through the opposite holes in the wheel rim. in the system » page ėěĕ. ›Screw the locking screw in the direction opposite of arrow until it stops ›Have the tightening torque of the wheel bolts checked with a torque wrench» Fig. Ęęė. as soon as possible. 0he prescribed tightening torque is Ėęĕ Nm.›Replace the box with the tool kit into the wheel and secure it with the tape. ›Fold back the floor covering or insert the variable loading floor and fold back Replace the damaged tyre. It is not recommended to repair the tyre.  the floor covering. ėĞė Do-it-yourself

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders