Alfa Romeo 33 owners manual page 238

text version of content this owner's manual page from owners manual to the vehicle Alfa Romeo 33, year of production 1983 - 1995:

REAR SUSPENSION COIL SPRINGS Flexible hose connections 9.8 t 14.7N- m (I + 1.5kg-m REMOVAL 7.23 + 10.85ft.lb) Remove co.il springs with the same . Adjust parking brake lever procedure followed for removal of stroke (see: Group 00- Mainte- shock absorbers; only remember not nance of Mechanical Compo- to disjoin shock absorber from upper nents and Body). body coupling. M L A.2.0070 REMOVAL If necessary, disassemble axle as follows: 4. Slightly lift column hoist and CHECKS AND INSPECTIONS 1. Release and remove bolts secur- remove the previously loosened tie 1. Verifthe springs has noy ing tie rods to axle; remove tie rods. rod and Panhard bar bolts. stretches or deformations. 2. If necessary, disassemblesilent- 5. Slowly lower hoist driving the 2. Verify spring efficiency by com- blocks from tie rods andPanhard bar axle and extracting the brake by using adequate bases and ex- paring its stiffness values with the adjustment spring from stud on the tractors. prescribed ones (see: Service Data Panhard bar. and Specifications). 3. Check wear status, verify pres- Assemble again the whole suspension ence of damages or deformations of on the car by theinversed procedure rubber components. Replace if than for removal. necessary. IMPORTANT INSTALLATION . With static load car (see: Group 00 - Maintenance of Mechanical Assemble coil springs onto car again Components and Body) set the in theinversed order of removal and bolts securing tie rods and bear in mind all indications and notes Panhard bar to the prescribed reported in paragraph Shock Ab- torque. 3. Extract dust cover from brake sorbers Installation. drum and caulk wheel hub nut. @) : Tightening Torque Remove nut and drum complete with Tie rod andPanhard bar securing bolts hub and bearings. REAR RIGID AXLE 4. Screw out connection 2 of 33.35 + 38.26N-m 0 (3.4 + 3.9 kg-m brake hydraulic system rigid tube on REMOVAL AND 24.58 f 28.2 ft-lb) jaw control cylinders and remove INSTALLATION rear tubes @. 5. Screw out and remove nuts@ Lubricate with prescribed grease Place car on hoist bridge, support its fastening stem pin and brake shoe (AGIP Fl Grease 15) the hole in 7 rear part by placing some stands in plate @J to rear axle. the brake adjustment spring the jack seats and remove the whole rear suspension as follows. support stud on thePanhard bar 1. Remove wheels. and the fork. Carry out brake adjustment 2. Working from passenger com- spring calibration (see: Group 22 partment, remove rear console for - Brake Adjustment). parking brake equalizer to be ac- Set the brake hydraulic system cessible. Then act on adjustment fork connections to the prescribed nut and lock nut and loosen parking torque and perform air bleeding brake control cables as much as to (see: Group 22- Brake System allow their releasing from equalizer; Air Bleeding). extract them from sheath locking bracket. @ : Tightening Torque 3. After providing the column hoist Rigid tube connections with support A.2.0070, remove coil 7.85 + 9.8 N-m springs with caps and gaskets (see: Coil Springs- Removal). (0.8 + 1 kg-m 1 Block shoe plate3 Nuts 5.78 - 7.23 ft-lb) 2 Connection 4 Rear tubes 25-f May 1983

owners manual Alfa Romeo 33

owners manual Alfa Romeo 33 - year of production: 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995 - Alfa Romeo 33 owners manual EN