owners manual Skoda Citigo

all ratings: 0 average rating: 5

Inflating Check after driving for Ėĕ minutes › Screw the tyre inflation hose Ě » Fig. ĖĖĚ on page ĖĘĘ of the air compressor firmly onto the tyre valve. First read and observe the introductory information and safety warn- › Check that the air release valve Ĝ is closed. ings on page ĖĘė. ä › Start the engine and run it in idle. › Plug the connector Ğ into Ėė 2olt socket » page ęě, Ėė-volt power socket. Check the tyre inflation pressure after driving for Ėĕ minutes! › Switch on the air compressor with the ON and OFF switch ĝ . If the tyre inflation pressure is Ė.Ę bar or less: › Allow the air compressor to run until a pressure of ė.ĕ - ė.Ě bar is achieved. ›  Do not drive the vehicle! 5ou cannot properly seal with tyre with the break- Maximum run time of ĝ minutes » ! down kit. › Switch off the air compressor. › Get professional assistance. › If you cannot reach an air pressure of ė.ĕ – ė.Ě bar, unscrew the tyre inflation hose Ě from the tyre valve. If the tyre inflation pressure is Ė.Ę bar or more: › Drive the vehicle Ėĕ metres forwards or backwards to allow the sealing agent to › Adjust the tyre inflation pressure to the correct value (see inside of fuel filler “distribute” in the tyre. cap). › Firmly screw the tyre inflation hose Ě back onto the tyre valve and repeat the › Continue driving carefully to the nearest ŠKODA specialist garage at a maxi- inflation process. Ð mum speed of ĝĕ km/h (Ěĕ mph). › If you cannot reach the required tyre inflation pressure here either, this means the tyre has sustained too much damage. 5ou cannot seal with tyre with the breakdown kit » . Jump-starting › Switch off the air compressor. › Remove the tyre inflation hose Ě from the tyre valve. Once a tyre inflation pressure of ė.ĕ – ė.Ě bar is achieved, continue the journey atäIntroduction a maximum speed of ĝĕ km/h (Ěĕ mph). 0his chapter contains information on the following subjects: Check the tyre inflation pressure after driving for Ėĕ minutes » page ĖĘę. Jump-starting ĖĘĚ 3ARNING Jump-starting in vehicles with the S0AR0-S0OP system ĖĘě ■ 0he battery of another vehicle can be used to jump-start your vehicle if the en- During inflation, the tyre inflation hose and air compressor may get hot- risk gine will not start because the battery is flat. Jump-start cables are required for of injury! ■ this purpose. Do not place the hot tyre inflation hose or hot air compressor on flammable materials – risk of fire! Both batteries must have a rated voltage of Ėė 2. 0he capacity (Ah) of the battery ■ If you cannot inflate the tyre to at least ė.ĕ bar, this means the damage sus- supplying the power must not be significantly less than the capacity of the dis- tained was too serious. 0he sealing agent cannot be used to seal the tyre.  charged battery in your vehicle. Do not drive the vehicle. Get professional assistance! Jump-start cables Only use jump-start cables which have an adequately large cross-section and in- CA10ION sulated terminal clamps. Observe the manufacturer's instructions. Switch off the air compressor after running ĝ minutes at the latest – danger ofPositive cable – colour coding in the majority of cases is red. overheating! Allow the air compressor to cool a few minutes before switching it Negative cable – colour coding in the majority of cases is black. £ Ð on again. ĖĘę Do-it-yourself

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders