owners manual Skoda Citigo

all ratings: 0 average rating: 5

Briefly press the rocker button B into the position RES to resume the storedSwitching the S0AR0-S0OP system on and off Ð speed after the clutch or brake pedal is released. system can be switched on/off by pressing the button » Fig. ěĞ. 0he S0AR0/S0OP 3hen start-stop mode is deactivated, the warning light in the button lights up. Switching off the cruise control system completely If the vehicle is in the stop phase when manually switching off the system, the engine starts immediately. First read and observe the introductory information and safety warn- 0he S0AR0-S0OP system is very complex. Some of the procedures are hard to ings on page ěĘ. ä check without servicing. 0he general conditions for the proper functioning of the Ð S0AR0-S0OP system are listed in the following overview. › 0urn the switch A » Fig. ěĝ on page ěę » page ěę into the OFF position. Conditions for the automatic engine shut down (stop phase) ›0he gearshift lever is in Neutral. S0AR0/S0OP ›0he clutch pedal is not depressed. ›0he driver has fastened the seat belt. ›0he driver's door is closed. Fig. ěĞ ›0he bonnet is closed. Button for the S0AR0-S0OP sys- ›0he vehicle is at a standstill. tem ›0he engine is at operating temperature. ›0he charge state of the vehicle battery is sufficient. ›0he stationary vehicle is not on a steep slope or a steep downhill section. ›0he engine speed is less than Ė ėĕĕ rpm. ›0he temperature of the vehicle battery is not too low or too high. ›0here is sufficient pressure in the braking system. ›0he difference between the outdoor- and the set temperature in the interior is not too great. 0he S0AR0-S0OP system helps you to save fuel while at the same time reducing ›0he vehicle speed since the last time the engine was switched off was greater harmful exhaust emissions and CO emissions. ė than Ę km/h. ›0he front wheels are not turned excessively (the steering angle is less than Ę/ę 0he function is automatically activated each time the ignition is switched on. of a steering wheel revolution). In the start-stop mode, the engine automatically switches to the vehicle's idle phase, e.g. when stopped at traffic lights. Conditions for an automatic restart (start phase) ›0he clutch is depressed. Information regarding the current state of the S0AR0-S0OP system is indicated in ›0he max./min. temperature is set. the display of the instrument cluster. ›0he defrost function for the windscreen is switched on. Automatic engine shut down (stop phase) ›A high blower stage has been selected. Stop the vehicle (where necessary, apply the handbrake). ›0he S0AR0 S0OP button is pressed. › › 0ake the vehicle out of gear. Conditions for an automatic restart without driver intervention › Release the clutch pedal. ›0he vehicle moves at a speed of more than Ę km/h. Automatic renewed engine restart (start phase). ›0he difference between the outdoor- and the set temperature in the interior is Depress the clutch pedal. too great. › ›0he charge state of the vehicle battery is not sufficient. 0here is insufficient pressure in the braking system. £ › Starting-off and DrivingěĚ

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders