owners manual Mercedes C

all ratings: 0 average rating: 5

BA 204 USA, CA Edition A 2011; 1; 5, en-US2010-05-20T09:17:30+02:00 - Seite 310 hereepe Version: 3.0.3.6 310 Service products and capacities overheating. In the Service Booklet, you can Coolant find information on the intervals for renewal. Important safety notes The renewal interval is determined by the coolant type and the cooling system design. The coolant is a mixture of water and The renewal interval in the Service Booklet is antifreeze/corrosion inhibitor. It performs only valid if the coolant is added or renewed the following tasks: with Mercedes-Benz approved products. R anti-corrosion protection Therefore, only use MB 326.0 antifreeze/ R antifreeze protection corrosion inhibitor or another Mercedes-Benz R raising the boiling point approved product of the same specification. The cooling system is filled with coolant at the Information on other Mercedes-Benz factory which contains antifreeze/corrosion approved products of the same specification inhibitor that ensures protection down to can be obtained at any authorized Mercedes- approximately -35 ‡ (-37 †). Benz Center or on the Internet at http://bevo.mercedes-benz.com. ! Only add coolant that has been premixed The coolant is checked at every service date with the desired antifreeze protection. You at an authorized Mercedes-Benz Center. could otherwise damage the engine. The antifreeze/corrosion inhibitor Further information on coolants and on concentration in the cooling system should: filling can be found in the Mercedes-Benz Specifications for Service Products, MBR be at least 50%. This will protect the cooling Approval 310.1, e.g. on the Internet at system against freezing down to around http://bevo.mercedes-benz.com. You -35 ‡ (-37 †). can also consult an authorized Mercedes- R not exceed 55% (antifreeze protection Benz Center. down to -49 ‡ (-45 †); otherwise, heat will not be dissipated as effectively. ! Always use a suitable coolant mixture, even in countries where high temperaturesIf the coolant level is too low, MB 326.0 prevail. antifreeze/corrosion inhibitor should be added. Have the cooling system checked for Otherwise, the cooling system will not be leaks. Technical datasufficiently protected from corrosion, and the boiling point will be too low. If the coolant has antifreeze protection down Windshield and headlamp cleaning to -35 ‡ (-37 †), the boiling point of the system coolant in the pressurized system is approximately 266 ‡ (130 †). Warning G Your vehicle has a range of aluminum Washer solvent/antifreeze is highly components. Use of aluminum components flammable. Do not spill washer solvent/ in the engine make it necessary to specifically antifreeze on hot engine parts, because it may match the antifreeze/corrosion inhibitor in ignite and burn. You could be seriously these systems in order to protect the burned. aluminum parts. Using other antifreeze/ XUse MB Windshield Washer Concentrate corrosion inhibitors without these characteristics affects the service life.MB SummerFit. XAt temperatures above freezing: add 1 The coolant must be used throughout the year in order to maintain the necessary corrosionpart MB SummerFit to 100 parts water, e.g. protection and provide protection from

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders