owners manual Mercedes GLK

all ratings: 0 average rating: 5

296 Features XTurntheSmartKeytoposition2intheigni-Synchronizing the rolling code tion lock (Y page 149). Payattention to the "Important safety notes" XSelect one of buttons ; to ? to use to(Y page 295). control the garage door drive. If the garage door systemusesarollingcode, XTostartprogramingmode:pressand you will also have to synchronize the garage door system with the integrated garage door hold one of buttons ; to ? on the inte- openerintherear-viewmirror.Todothisyou grated garage door opener. will needtousetheprogramingbuttononthe Thegaragedooropenerisnowinprogram- doordrivecontrolpanel.Theprogramingbut- ing mode. After a short time, indicator ton may be positioned at different locations lamp :lights up yellow. depending on the manufacturer. It is usually Indicator lamp : lights up yellow as soon located on the door drive unit on the garage asbutton;,=or?isprogramedforthe features ceiling. first time.Iftheselectedbuttonhasalready Familiarize yourself with the garage door been programed, indicator lamp : will and drive operating instructions, e.g. under "Pro- only light up yellow after ten seconds have graming of additional remote controls", elapsed. before carrying out the following steps. XReleasebutton ;,=or?.Indicator Your vehicle must be within reach of the lamp :flashes yellow. garage door or gate opener drive. Make sure XToprogramtheremotecontrol:point Stowage that neither your vehicle nor any persons/ garage door remote control A towards objects are present within the sweep of the buttons;to?ontherear-viewmirrorat door or gate. a distance of 2 to 8 inches (5 to 20 cm). XTurntheSmartKeytoposition2intheigni- XPressandholdbuttonBonremotecontrol tion lock (Y page 149). Auntilindicator lamp : lights up green. Whenindicator lamp : lights up green:XGetoutofthevehicle. programing is finished. XPresstheprogramingbutton on the door Whenindicatorlamp:flashesgreen:pro-drive unit. gramingwassuccessful.Thenextstepisto Usually, you now have 30 seconds to ini- synchronize the rolling code. tiate the next step. XReleasebuttonBonremotecontrolAfor XGetintothevehicle. the garage door drive system. XPresspreviously programed button ;, = If indicatorlamp:lightsupred:repeatthe or?ontheintegratedgaragedooropener programing procedure for the correspond- until the door closes. ing button on the rear-view mirror. When The rolling code synchronization is then doingso,varythedistancebetweenremote complete. control A and the rear-view mirror. The required distance between remoteNotesonprogramingtheremotecontrol control A and the integrated garage door Canadian radio frequency laws require a opener depends on the garage door drive "break" (or interruption) of the transmission system. Several attempts might be neces- signals after broadcasting for a few seconds. sary. You should test every position for at Therefore, these signals may not last long least 25 seconds before trying another enough for the integrated garage door position. opener. The signal is not recognized during programing. Comparable with Canadian law, someU.S.garagedooropenersalsofeaturea "break".

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders