text version of content this owner's manual page
from owners manual to the vehicle Alfa Romeo 33, year of production 1983 - 1995:
COMPLETE CAR
Engine controls Heating system Doors and bonnets
- - - Visually check all weather-
Check proper working condition
Check and make sure starter
of levers controlling heater and
stripping for tight fit and make
control knob works freely,
outlets for admission of air into
sure they are not damaged, out
without sticking; further check
the vehicle (open and close).
of shape or dirty.
that when this knob is pushed
- Check if electric fan works
in, respective device is not at all -y See if doors and bonnets are
properly at different speeds and
engaged on carburetor. aligned andcentered with rele-
- if relevant warning light on the
vant openings.
Check accelerator pedal and
board lights up.
make sure it does not stick; also
check that when pedal is pushed Seats, seat belt andac!essory equip-
Lights, signal,electrical accessory
ment
down all the way, throttle valve
is fully open. equipment - After having removed relevant
- With ignition key set to“MAR”
protecting covers, inspect seats
check if lights outside and inside
checking if they slide freely on
Brake, clutch and gearbox controls
the vehicle, as well as relevant
tracks without sticking and
- With engine running, push brake
warning lights, go on: front
pedal and check if” after the noiselessly. Also check proper
and rear parking lights, number
initial stroke- it comes without working condition of seat and
plate lights, direction indicators
elasticity. head-rest adjusting devices.
and emergency flasher, stop
-
Also check if parking brakeCheck if seat belts and relevant
lights,high and low beam
retractors are in good working
control lever works properly.
headlights,headlights flasher,
- With engine running, push clutch condition.
reverse gear lights, rear fog lightsinside
pedal down and make sure that - Check and outside
inside ceiling lamp (through
all gearbox speeds engage easily, rear-view mirrors making sure
manual as well as door switch),
without sticking and noiselessly. they swing easily and stay firmly
instrument cluster light. in place when set; also check
- Check proper working conditionmirror for
Tightening wheel screws snapswitch on
- of following warning lights:
Use a spanner and check if wheel day/night driving.
alternator, fuel reserve, oil pres-
- Check maneuverability ofsun-
screws, are properly tightened.
sure, brake fluid level, parking
visors, ashtrays, glove compart-
Also check if screws, are in
brake on, starter on, defroster
compliance with vehicle and rim ment and any other accessory.
on, cooling water temperature.
type, as shown in the Spare Parts
Catalogue. - Check proper operation of horns
and cigarette lighter. CLEANING AND
Dashboard instruments FINISHING
- Windshield and rear window wiper
While starting up the engine,
and washer
check if all electrically con-
INSPECTION
- After having installed wiper
trolled instruments work proper-
blades, check if windshield wiper
ly (needles are moving): rpm
Exterior cleaning
works properly at both speeds as
indicator, oil pressure gauge, -
If required, dewax the vehicle
well as it is set to intermittent
water temperature gauge, fuel
suitable products
level indicator, and clock. operation. using and
procedures; wash the vehicle’s
- Operate the windshield washer
exterior with a solution of
System circuits tightness and check if sprayer jets are
- water and shampoo, rinse it
normal and properly directed
Visually check circuits of follow-
thoroughly and dry it.
toward the windshield’s higher
ing systems for leaks or evidence
section. Finish up cleaning by removing
thereof: fuel, brake, clutch, and
engine cooling. any stubborn spots by means of
- Locks, hinges, windows suitable compounds.
Check engine, gearbox and dif-
- Check proper working condition
ferential for evidence of oil
Paint
leaks. of all door locks (close, lock,
- Visually and thoroughly check
open from inside and outside).
Engine cooling electric fan all painted surfaces and remove
Check in the same manner also
- Connect and short-circuit wires
accidental or
locks of engine and back door.manufacturing
of radiator thermal contact and flaws, if any.
- Check door and bonnet hinges
check if fan starts and works
for smooth noiseless operation.
properly. - Check if windows can be openedExterior/Interior mouldings and fit-
Also make sure that wires are
and closed all the way without
tings
properly and securely connected - Visually check all vehicleout- ’s
sticking and noiselessly.
to thermal contact.
00-9 May 1983
this site is maintained by advertising - for view instructions, turn off ad blocking in your browser