or
owners manual Hummer H2
owners manual Hummer H2 - year of production: 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 - Hummer H2 owners manual EN
Document: pdf (3.37 MB) 468 pages
all ratings: 0 average rating: 5
text version of content this owner's manual page from owners manual to the vehicle Hummer H2, year of production 2002 - 2010:
3. Simultaneously press and hold both the desired 6. Locate in the garage, the garage door opener
button on HomeLink® and the hand-held transmitter receiver (motor-head unit). Locate the “Learn”
button. Do not release the buttons until Step 4 or “Smart” button. This can usually be found where
has been completed. the hanging antenna wire is attached to the
Some entry gates and garage door openers may motor-head unit.
require you to substitute Step 3 with the procedure 7. Firmly press and release the “Learn” or “Smart”
noted in “Gate Operator and Canadian button. The name and color of the button may
Programming” later in this section. vary by manufacturer.
4. The indicator light will flash slowly at first and then You will have 30 seconds to start Step 8.
rapidly after HomeLink® successfully receives the 8. Return to the vehicle. Firmly press and hold the
frequency signal from the hand-held transmitter. programmed HomeLink® button for two seconds,
Release both buttons. then release. Repeat the press/hold/release
5. Press and hold the newly-trained HomeLink® button sequence a second time, and depending on the
and observe the indicator light. brand of the garage door opener (or other rolling
If the indicator light stays on constantly, code device), repeat this sequence a third time
programming is complete and your device should to complete the programming.
activate when the HomeLink® button is pressed and HomeLink® should now activate your rolling-code
released. equipped device.
To program the remaining two HomeLink® buttons, ®
® To program the remaining two HomeLink buttons,
begin with Step 2 under “Programming HomeLink .” ®
Do not repeat Step 1 as this will erase all of the begin with Step 2 of “Programming HomeLink .” Do not
programmed channels. repeat Step 1.
If the indicator light blinks rapidly for two seconds
and then turns to a constant light, continue with
Steps 6 through 8 following to complete the
programming of a rolling-code equipped device
(most commonly, a garage door opener).
2-52
Download PDFClick here to download a pdf file with an instruction manual for Hummer H2
year of production from: 2002
Do you prefer pdf format?Find out how to download
Enter the code to download PDF file:
:
All pages in one PDF file!
How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.
How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.
:
Hummer H2 owners manual
pages 125 - 131
pages 125 - 131
Hummer H2 owners manual
page 128 / 468
this site is maintained by advertising - for view instructions, turn off ad blocking in your browser
Download PDFOther available language versions of this manual:
- Hummer H2 manuel du proprietaire FRshow the owner's manual
pdf - 5.22 MB
Others owner's manuals for this model:
Hummer H2 2002 - 2010 EN - Hummer H2 owners manual - pdf - 3.51 MB
Hummer H2 2002 - 2010 FR - Hummer H2 manuel du proprietaire - pdf - 5.22 MB
Hummer H2 2002 - 2010 EN - Hummer H2 owners manual - pdf - 3.51 MB
Hummer H2 2002 - 2010 FR - Hummer H2 manuel du proprietaire - pdf - 5.22 MB